A set of 3 replacement Ceramic Impeller Shafts for Biolife 35 & 55 motors with ceramic shafts.


Removal & Fitting Tools included

Instructions for changing Ceramic Shaft

1. Turn and remove impeller housing cover


2. Remove impeller


3. Prise off the motor end cover (where elec cable
   enters)


4. Insert steel shaft tool into hole and push with
   black plastic fitting until ceramic shaft emerges at other end


5. Insert new ceramic shaft into  black plastic
   tool and push into bottom of impeller housing recess until fully seated


6. Refit motor end cover


7. Refit impeller and housing cover

Replacement motor head for both the Biolife 35 and 55

Comes complete with ceramic shaft installed

Short mains lead for connection into existing Biolife electrical system

Impeller is NOT included

Plastic support bracket complete with rubber suction cups and aluminium straps

Spares for the earlier Biolife model with internal heater : A252

Mech Duo Cartridge

The BioLife Mech Duo-Density Polyester / Carbon Cartridge is the third and final step in mechanically scrubbing the passing water flow. The Duo Density polyester pad removes any fine solid wastes that escapes Stage 1 and 2. Following the final step in mechanical filtration, the carbon granules within adsorb liquefied wastes, medications or dyes into the huge internal carbon matrix. The efficient combination of micro and macro pores adsorbs all sizes of liquefied wastes and gaseous impurities in the water stream before they can reach the "Dry" Chamber

Maintenance:

Thwe BioLife Stage 3 Duo-Density Polyester / Carbon Cartridges should be changed every two weeks to ensure water flow to the biological filter is pure.

Pull old cartridge from the slot, discard and insert a new one into the empty slot. Ensure the arrows are facing down.

Spares for the later Biolife model without an internal heater : A255

Carbon Filter Stage 2

The BioLife's Carbon Filter is the second step in mechanically scrubbing the passing water flow. The filter removes any fine solid wastes that escapes Stage 1 . A huge internal carbon matrix adsorbs liquefied wastes, medications or dyes . The efficient combination of micro and macro pores adsorbs all sizes of liquefied wastes and gaseous impurities in the water stream before they can reach the "Dry" Chamber

Maintenance:

The Carbon Filter should be changed every two weeks to ensure water flow to the biological filter is pure.

Pull old carbon filter from the slot of the mechanical media holder, discard and insert a new one into the empty slot.

A-280 BioLife Stage 4 Bio Core

The BioLife Ceramic Filter Core provides the perfect place for beneficial bacteria to colonize and thrive.

The core should be removed and washed in aquarium water when clogged.

One half of the core should be replaced every 6 months

1 Complete Core : supplied as two halves

Bio Hex-Nodes

BioLife Stage 5

"Wet / Dry" Filtration System Media

The Bio-Life Hex-Nodes may be used either in a "dry" chamber or submersed in a water flow. They provide ideal surface attachment points for the beneficial bacteria to grow and thrive. Used in the lowest biological chamber of the BioLife Filtration System, they provide the finishing biological polishing of the water before it is exhausted into the aquarium.

Hex-Nodes require almost no maintenance. If there is any build up of deposits on the pieces, simply rinse the Hex-Nodes in aquarium water to ensure the bacterial populations are retained as solid wastes are washed away. Normal tap water supplies include Chlorine and Chloramine in the water that will kill most of the beneficial colonies of bacteria and should be carefully avoided when rinsing any biological media.

If desired, change half the Hex-Nodes 6 monthly. It takes time for an adequate population of bacteria to grow to a strength where they can remove all the ammonia and nitrite produced by the aquarium. When changing Hex-Nodes that have been previously initiated, do not change any other media at the same time. bacteria already in the filter and media will rapidly seed the Hex-Nodes

Net Wt. 17 oz / 500gm ART.# A-282